These panels are machined out of 6061-T6 billet aluminum. They are a direct replacement for the stock plastic panels used on Trim Master and Bennett rocker switches as well as the LED Indicators. They will also work with Bennett rocker switches or our Military Rocker switches. Available in a bright polished finish or in a variety of anodized colors.

Manufactured from stainless steel, these cable seals work with 33C cables to provide a seal where they pass through the transom.

Replacement relay box for Eddie Marine trim tabs. Also for use with hatch actuators. By incorporating one of these boxes, the possibility of voltage drop will be eliminated and the actuator will be supplied with a full 12 volts of current at all times, regardless of the length and age of the power supply wires. This will insure that your actuator will operate at its maximum speed. The relay box incorporates two relays that are encapsulated in epoxy for corrosion resistance. The relay box also allows the use of a single pole switch to operate reverse polarity actuators and can accommodate two actuators simultaneously.  NOTE: ALL SALES ARE FINAL ON ELECTRIC PARTS - NO RETURNS, REFUNDS, OR EXCHANGES.

These kits are used to attach a 33C mechanical trim indicator cable to our trim tabs. Mil spec hard coat anodized for corrosion resistance. Comes with stainless steel fasteners and cable clamp. Order cable seals separately.

Designed for use with our 500-78500-77 trim tabs. The kit includes a dual switch panel with the color of your choice. The wire harness includes 26' of color-coded twisted wire, fuse holders, and all necessary wire and connectors. Some crimping and cutting is required.

Mechanical indicators are the most accurate method of monitoring the position of your sterndrive, outboard or trim tab. Unlike electric trim gauges, they are mechanically operated by a push-pull cable, eliminating the need to rely on an irritating "floating" needle. All indicators sold by Eddie Marine feature all billet aluminum construction including fully customizable faces. For a complete mechanical indicator system you must purchase the indicator as well as an actuator, a 33c cable and transom cable seal for each drive or tab you wish to monitor. When ordering, specify layout of the indicator (horizontal or vertical) as well as desired direction of the cable entry (top, bottom, left or right) and the type of actuator you are using. Dimensions for 1 and 2 slot panels is 2 1/2" w x 5" h

Mechanical indicators are the most accurate method of monitoring the position of your sterndrive, outboard, or trim tab. Unlike electric trim gauges, they are mechanically operated by a 33C push-pull cable, eliminating the need to rely on the irritating "floating" needle of a trim gauge. All indicators sold by Eddie Marine feature all billet aluminum construction including fully customizable faces. For a complete mechanical indicator system you must purchase the indicator as well as an actuator, a 33c cable and transom cable seal for each drive or tab you wish to monitor.Dimensions for 1 and 2 slot panels is 2 1/2" w x 5" h

Mechanical indicators are the most accurate method of monitoring the position of your sterndrive, outboard, or trim tab. Unlike electric trim gauges, they are mechanically operated by a 33C push-pull cable, eliminating the need to rely on the irritating "floating" needle of a trim gauge. All indicators sold by Eddie Marine feature all billet aluminum construction including fully customizable faces. For a complete mechanical indicator system you must purchase the indicator as well as an actuator, a 33c cable and transom cable seal for each drive or tab you wish to monitor.Dimensions for 3 and 4slot panels is 3 3/4" w x 5" h

This trim actuator is used to attach a 33C control cable to your dash mounted mechanical indicator. The actuator mounts on the trim ram of your Mercury Bravo or IMCO sterndrive or Mercury outboard. The kit includes all of the necessary parts to mount one actuator to a cylinder.
;

Mechanical indicators are the most accurate method of monitoring the position of your sterndrive, outboard, or trim tab. Unlike electric trim gauges, they are mechanically operated by a 33C push-pull cable, eliminating the need to rely on the irritating "floating" needle of a trim gauge. All indicators sold by Eddie Marine feature all billet aluminum construction including fully customizable faces. For a complete mechanical indicator system you must purchase the indicator as well as an actuator, a 33c cable and transom cable seal for each drive or tab you wish to monitor.

Mechanical indicators are the most accurate method of monitoring the position of your sterndrive, outboard, or trim tab. Unlike electric trim gauges, they are mechanically operated by a 33C push-pull cable, eliminating the need to rely on the irritating "floating" needle of a trim gauge. All indicators sold by Eddie Marine feature all billet aluminum construction including fully customizable faces. For a complete mechanical indicator system you must purchase the indicator as well as an actuator, a 33c cable and transom cable seal for each drive or tab you wish to monitor.Dimensions for 3 and 4slot panels is 3 3/4" w x 5" h

Replacement hydraulic pump for Eddie Marine trim tabs using relays.